Just How to Set up a Tub
Just How to Set up a Tub
Blog Article
Were you interested in help on Installing A Bathtub?
Installing a tub isn't exactly rocket science, yet it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably challenging job. If the old bathtub is readily easily accessible, the project can move immediately; if you have to open a wall to get rid of the old tub as well as place the brand-new bathtub, the job is a lot harder. In either situation, the task is within a residence handyman's skills, although you will need an assistant to leave the old bathtub and also embeded in the brand-new one. Make sure you have actually certified on your own for the task and also are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is far better to consider employing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will certainly assist you set up a brand-new tub in your shower room if you have actually currently bought a new tub and also do not require to transform the setup of your previous supply of water pipes.
Your tools as well as product checklist need to make up the following:
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of removing the existing faucets can be fairly troublesome because of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Prior to carrying on to fit the new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the tap in position with the maker supplied backnut. Once the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the called for setting. The wood boards are practical in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bath tub up until the level checks out degree.
To set up faucets, fit the bottom of the outermost versatile faucet connector to the proper supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the supply of water and also inspect all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as also inspect the overflow outlet as well as the regular outlet for leakages.
Ultimately, fix the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has been utilized a minimum of when as this will certainly resolve it into its last position.
Planning for the Installment
Firstly, the sustaining frame supplied with the bathroom needs to be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid stress on the tub.
Fit the adaptable faucet adapters to the bottom of the two taps using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing problems with moisture as well as possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to allow for the movement experienced when the bathtub is in use. The sealer can split relatively early if you do not take into account this activity before securing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that write up about Installing A Bathtub when doing a lookup on the internet. Sharing is caring. Helping people is fun. Bless you for your time. Come back soon.
Schedule
Report this page